由 kevintyk » 週二 6月 08, 2004 1:24 pm
企鵝狂 寫:請把XF86Config-4的
Section "Device"
Identifier "Generic Video Card"
Driver "radeon"
Option "UseFBDev" "true"
EndSection
Driver改成 fglrx
那個Option移除
或者..你裝好ATi的driver以後.他有一個工具幫你設定.叫做fglrxconfig
建議你跑這個flgrxconfig..因為他還會設定一些Option...
跑完就會設定好了
真的會是 AGP 模組的緣故嗎？
由 企鵝狂 » 週二 6月 08, 2004 1:33 pm
kevintyk 寫:我以前也試過....
同樣的不行
[
由 kclin » 週二 6月 08, 2004 1:49 pm
由 kevintyk » 週二 6月 08, 2004 2:28 pm
企鵝狂 寫:kevintyk 寫:我以前也試過....
同樣的不行
[
把你那樣子設定時候的XF86Config-4跟Xfree86.0.log 貼上來看看
kernel module有重新編譯過了嗎?
dmesg說甚麼
lsmod?
dmesg
Linux version 2.4.26-1-k7 (herbert@gondolin) (gcc version 3.3.3 (Debian 20040401)) #1 Sat May 1 21:40:09 EST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 Nvidia ) @ 0x000f74b0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff7e00
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Kernel command line: root=/dev/hdd3 ro
Found and enabled local APIC!
Initializing CPU#0
Detected 1409.458 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2811.49 BogoMIPS
Memory: 252588k/262080k available (1207k kernel code, 9104k reserved, 459k data, 112k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1600+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1409.4691 MHz.
..... host bus clock speed is 268.4702 MHz.
cpu: 0, clocks: 2684702, slice: 1342351
CPU0<T0:2684688,T1:1342336,D:1,S:1342351,C:2684702>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router default [10de/01e0] at 00:00.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3932 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 3932k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 112k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: 00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y120P0, ATA DISK drive
blk: queue d082a100, I/O limit 4095Mb (mask 0xffffffff)
hdc: AOPEN CD-RW CRW2440, ATAPI CD/DVD-ROM drive
hdd: IC35L060AVVA07-0, ATA DISK drive
blk: queue d082a690, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=238216/16/63, UDMA(133)
hdd: attached ide-disk driver.
hdd: 120103200 sectors (61493 MB) w/1863KiB Cache, CHS=119150/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [14946/255/63] p1 p2
/dev/ide/host0/bus1/target1/lun0: [PTBL] [7476/255/63] p1 p2 p3 p4
Journalled Block Device driver loaded
ext3: No journal on filesystem on ide1(22,67)
Adding Swap: 265064k swap-space (priority -1)
Real Time Clock Driver v1.10f
MSDOS FS: Using codepage 950
MSDOS FS: IO charset big5
MSDOS FS: Using codepage 950
MSDOS FS: IO charset big5
Intel 810 + AC97 Audio, version 0.24, 22:21:02 May 1 2004
PCI: Setting latency timer of device 00:06.0 to 64
i810: NVIDIA nForce Audio found at IO 0xd400 and 0xd000, MEM 0x0000 and 0x0000, IRQ 11
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
PCI: Setting latency timer of device 00:04.0 to 64
eth0: forcedeth.c: subsystem: 01695:1000 bound to 00:04.0
8139too Fast Ethernet driver 0.9.26
eth1: RealTek RTL8139 at 0xa000, 00:04:61:5e:15:a2, IRQ 11
eth1: Identified 8139 chip type 'RTL-8101'
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:02.2 to 64
ehci_hcd 00:02.2: nVidia Corporation nForce2 USB Controller
ehci_hcd 00:02.2: irq 11, pci mem d08f6000
usb.c: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 00:02.2
ehci_hcd 00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 6 ports detected
PCI: Setting latency timer of device 00:02.0 to 64
usb-ohci.c: USB OHCI at membase 0xd08fe000, IRQ 11
usb-ohci.c: usb-00:02.0, nVidia Corporation nForce2 USB Controller
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Setting latency timer of device 00:02.1 to 64
usb-ohci.c: USB OHCI at membase 0xd0900000, IRQ 5
usb-ohci.c: usb-00:02.1, nVidia Corporation nForce2 USB Controller (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 3 ports detected
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-uhci.c: $Revision: 1.275 $ time 22:24:23 May 1 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
eth0: no link during initialization.
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
eth1: link up, 10Mbps, half-duplex, lpa 0x0000
hub.c: new USB device 00:02.1-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x663/0x9906) is not claimed by any active driver.
hub.c: new USB device 00:02.0-2, assigned address 2
usb.c: USB device not accepting new address=2 (error=-110)
spurious 8259A interrupt: IRQ7.
hub.c: new USB device 00:02.0-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x66f/0x4200) is not claimed by any active driver.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input: USB HID v1.00 Gamepad [USB Game Device USB Game Device] on usb3:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
PPP BSD Compression module registered
PPP Deflate Compression module registered
[drm] Initialized radeon 1.7.0 20020828 on minor 0
[drm:radeon_unlock] *ERROR* Process 548 using kernel context 0
[drm:radeon_unlock] *ERROR* Process 719 using kernel context 0由 kclin » 週二 6月 08, 2004 2:42 pm
由 kevintyk » 週二 6月 08, 2004 2:45 pm
由 kclin » 週二 6月 08, 2004 2:53 pm
由 kevintyk » 週二 6月 08, 2004 3:03 pm
kclin 寫:必須先編出 fglrx module 然後 裝進 kernel 中才可以 dri
ps: 當你編 kernel 時
在 Loadable modules support 中 請將
Enable loadable module support 打勾及
module unload 打勾 同時取消 module versioning support 的功能
由 kevintyk » 週二 6月 08, 2004 3:11 pm
kclin 寫:你可以先試試直接打
sh make.sh
可以 work 嗎?
debian:/lib/modules/fglrx/build_mod# sh make.sh
ATI module generator V 2.0
==========================
initializing...
kernel includes at /usr/src/linux/include not found or incomplete
file: /usr/src/linux/include/linux/version.h
由 kclin » 週二 6月 08, 2004 3:16 pm
由 kclin » 週二 6月 08, 2004 3:24 pm
由 kclin » 週二 6月 08, 2004 3:27 pm
正在瀏覽這個版面的使用者：沒有註冊會員 和 1 位訪客
