kernel 2.4.18-686

[訪客]

請問一下, 我在把kernel版本升級成 2.4.20 後發現了我原先的IDE硬碟和作raid的IDE硬碟都在開機的時候它都會說有錯誤, 好像是偵測不到, super block有問題, 要我fsck或e2fsck但是我只要換回原來2.4.18版的就又可以了,這到底是為什麼呢?!是因為kernel版本可能原本不支援,我需要自己重編譯它嗎.?!

[cyt]

>在把kernel版本升級成 2.4.20 後
你是自己 compiler kernel source code 來升級的嗎?
會不會是 make config 時有東西沒編進去??

[訪客]

我是直接apt-get install kernel-image來升級的, 這樣它會漏掉IDE的支嗎.?!

[阿信]

您是用 soft raid or raid 卡上得 bios 呢？

如果是 raid 卡的話，要先確定 2.4.20 有支援您的 raid 卡喔

[訪客]

我是用soft raid模擬的, 不只是我的raid的硬碟
連我IDE的硬碟都不行, 只有SCSI硬碟它找的到..

[Tetralet]

或者，
請檢查一下您的 boot loader 之設定是否有誤？
（像是 LILO 的 root=/dev/hda1 之類的）

[訪客]

lilo的設定應該是沒有錯
我的開機訊息:
Freeing initrd memory: 3188k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 100k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 10 for device 00:0b.0
PCI: Sharing IRQ 10 with 00:07.0
sym53c8xx: at PCI bus 0, device 11, function 0
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
PCI: Found IRQ 11 for device 00:0b.1
PCI: Sharing IRQ 11 with 00:04.2
PCI: Sharing IRQ 11 with 00:04.3
sym53c8xx: at PCI bus 0, device 11, function 1
sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up)
sym53c8xx: 53c1010-33 detected with Symbios NVRAM
sym53c1010-33-0: rev 0x1 on pci bus 0 device 11 function 0 irq 10
sym53c1010-33-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-0: on-chip RAM at 0xf4800000
sym53c1010-33-0: restart (scsi reset).
sym53c1010-33-0: handling phase mismatch from SCRIPTS.
sym53c1010-33-0: Downloading SCSI SCRIPTS.
sym53c1010-33-1: rev 0x1 on pci bus 0 device 11 function 1 irq 11
sym53c1010-33-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-33-1: on-chip RAM at 0xf3800000
sym53c1010-33-1: restart (scsi reset).
sym53c1010-33-1: handling phase mismatch from SCRIPTS.
sym53c1010-33-1: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
blk: queue d3cc5c18, I/O limit 1048575Mb (mask 0xffffffffff)
sym53c1010-33-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50.0 ns, offset 15)
Vendor: IBM Model: DGVS09Y Rev: 03B0
Type: Direct-Access ANSI SCSI revision: 03
blk: queue d3cc5e18, I/O limit 1048575Mb (mask 0xffffffffff)
sym53c1010-33-0-<0,0>: tagged command queue depth set to 4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 17829870 512-byte hdwr sectors (9129 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 249832k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Found IRQ 5 for device 00:09.0
eth0: VIA VT6102 Rhine-II at 0xb400, 00:50:ba:20:39:1f, IRQ 5.
eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 45e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: could not lock [dev 03:00], zero-size? Marking faulty.
md: could not import [dev 03:00]!
md: autostart [dev 03:00] failed!
EXT2-fs warning (device sd(8,5)): ext2_read_super: mounting ext3 filesystem as ext2

EXT2-fs warning (device sd(8,6)): ext2_read_super: mounting ext3 filesystem as ext2

EXT2-fs warning (device sd(8,7)): ext2_read_super: mounting ext3 filesystem as ext2

EXT2-fs warning (device sd(8,8)): ext2_read_super: mounting ext3 filesystem as ext2

EXT2-fs: unable to read superblock
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:04.2
PCI: Sharing IRQ 11 with 00:04.3
PCI: Sharing IRQ 11 with 00:0b.1
uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:04.3
PCI: Sharing IRQ 11 with 00:04.2
PCI: Sharing IRQ 11 with 00:0b.1
uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
eth0: Setting full-duplex based on MII #8 link partner capability of 45e1.
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)

[訪客]

開機過程還會出現這樣的訊息:
dev/md0
The superblock could not be read or does not describes a correct ext2 filesystem If the device is valid and it really contains an ext2 filesystem (and not swap or ufs ot something else ), then the superblock is corrupt and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>

fsck fail, please repair mannually

[阿信]

跟小弟一樣的LSI的scsi卡耶...

您可以先掛載 ide-disk 來偵測系統的 ide 硬碟，小弟這邊是用 scsi 硬碟當主系統，ide當備份硬碟，開機時要手動載入 ide-disk 才會偵測到 所有ide 硬碟。

[訪客]

抱歉, 請問要如何掛載ide-disk....指的是mount嗎..?!

[訪客]

我mount 之後出現的訊息是:
modprobe : modprobe: Can't locate module block0-major-22
mount : /dev/hdc1 is not a valid block device

[阿信]

抱歉，沒說清楚，小弟的意思是載入 ide-disk 這個模組，就能夠偵測到您的ide硬碟才是

[訪客]

載入ide-disk模組後, 它還是沒有偵測到我的硬碟耶...仍是無法掛載起來

[阿信]

載入ide-disk模組後, 它還是沒有偵測到我的硬碟耶...仍是無法掛載起來

...這就奇怪了，要不要換成其他的 kernel 試試看呢？

BTW...kernel-2.4.20...Debian 官方應該沒有這個 pkg 了吧？

[訪客]

抱歉我前面有點打錯了 應該是2.4.22-2