驅動程式

[ccli0709]

一大堆I/O錯誤的問題,怎麼辦才好呢?

代碼: 選擇全部

SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335583
printk: 3 messages suppressed.
Buffer I/O error on device sda1, logical block 8791940
lost page write due to I/O error on sda1
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335591
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335599
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335607
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335615
printk: 3 messages suppressed.
Buffer I/O error on device sda1, logical block 8791944
lost page write due to I/O error on sda1
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70335623
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70354911
IT8212Interrupt: error!
MapError: error register is 84
IDE: command abort
SCSI error : <0 0 0 0> return code = 0x8000000
Info fld=0x0, Current sda: sense key Aborted Command
end_request: I/O error, dev sda, sector 70354919


[THQ]

安裝ite8212-RAID控制卡
1.到官方網站下載驅動程式原始碼:http://www.ite.com.tw/.
2.# cd /usr/src
3.# apt-get install kernel-headers-2.6.8.2 kernel-source-2.6.8
4.# bunzip kernel-source-2.6.8.tar.bz2
5.# cp -a /usr/src/kernel-source-2.6.8/drivers/scsi/{scsi,scsi_obsolete,scsi_typedefs}.h /usr/src/kernel-source-2.6.8/drivers/scsi/scsi_module.c /usr/src/kernel-source-2.6.8/include/scsi/scsi_host.h .
6.修改Makefile裡的KERNEL_SRC為/usr/src/kernel-headers-2.6.8-2-386
7.修改iteraid.c裡的hosts.h為scsi_host.h
7.# make
8.# install -m 644 iteraid.ko /lib/modules/2.6.8-2-386/kernel/drivers/scsi/
9.# depmod -a
10.# 加入iteraid到/etc/modules裡

照了上面方法試了,有編出iteraid.ko ...但最後還是不行..之前有成功過..看了一些人的文章和這一篇,但今天在照上面方法試..怎麼都跑不出來呢? ...真累.弄了好久

[THQ]

我重新在編譯一次發生錯誤

代碼: 選擇全部

make -C /usr/src/kernel-headers-2.6.8-2 SUBDIRS=/usr/src/src/2.6.x modules
make[1]: Entering directory `/usr/src/kernel-headers-2.6.8-2'
  CC [M]  /usr/src/src/2.6.x/iteraid.o
/usr/src/src/2.6.x/iteraid.c: In function `itedev_open':
/usr/src/src/2.6.x/iteraid.c:5579: warning: `MOD_INC_USE_COUNT' is deprecated (declared at

include/linux/module.h:555)
/usr/src/src/2.6.x/iteraid.c: In function `itedev_close':
/usr/src/src/2.6.x/iteraid.c:5816: warning: `MOD_DEC_USE_COUNT' is deprecated (declared at

include/linux/module.h:567)
/usr/src/src/2.6.x/iteraid.c: At top level:
/usr/src/src/2.6.x/iteraid.c:4666: warning: `IdeMediaStatus' defined but not used
  Building modules, stage 2.
  MODPOST
  CC      /usr/src/src/2.6.x/iteraid.mod.o
  LD [M]  /usr/src/src/2.6.x/iteraid.ko
make[1]: Leaving directory `/usr/src/kernel-headers-2.6.8-2'


[wsun013]

其實都是 warning, 應該不算錯誤
所以應該沒差的

[THQ]

其實都是 warning, 應該不算錯誤
所以應該沒差的

那即然沒差,怎麼會顯示不出來呢?
有什麼方法可以檢測的嗎